Part 1. Preparing the server.
The first thing we need to do is check to see if the remote desktop is activated. With this intention we follow the following path: Control Panel>System and Security>Advanced system settings. Once there, please select the Security tab. Verify that the box corresponding to Allow remote connections to this computer is checked.
https://www.rise.company/upload/uplo...2239086631.jpg
Allow remote connections. Create users who will connect by remote desktop.
Next, we will create the users who will be able to connect remotely to the server. We will then add these users to the corresponding group. To see in detail how to manage groups and users, please click
here. With this in mind, press the Win+X combination and select Computer Management.
https://www.rise.company/upload/uplo...2239137912.jpg
Select Computer Management. Then follow this path: Local users and groups>Users
https://www.rise.company/upload/uplo...2239144963.jpg
At this point, add users who will be able to connect by the remote server. In this case, I will add 5 users, but you can add any number of users.
https://www.rise.company/upload/uplo...2239152554.jpg
Creating Remote Desktop Users Then go to the Groups section, and click on Remote Desktop Users.
https://www.rise.company/upload/uplo...2239159835.jpg
Adding users to the Remote Desktop Users group
Step 2. Downloading RDPWrapper
As mentioned above, to bypass this Microsoft ban we will use an opensource software called RDPWrapper. With this in mind, please go to the project’s GitHub page. There you can
download the zipped file.
https://www.rise.company/upload/uplo...2239164116.jpg
Download the zip file Then unzip the file to the location of your choice. Once the folder is unzipped, double click on the file install.bat
https://www.rise.company/upload/uplo...2239167877.jpg
Run install.bat The installation will begin immediately, please wait a few seconds while the installer does his job.
https://www.rise.company/upload/uplo...2239171988.jpg
RDPWrap installer Then click on RDPConf.exe. Wait until the program’s configuration tab loads. You can leave the default settings. Please note that all three diagnostic options must be green and fully supported. However, it is likely that the not supported warning will appear in red. If this happens, the program will not work and you will not be able to connect multiple users. But do not worry, we will solve this issue.
https://www.rise.company/upload/uplo...2239175519.jpg
RDPWrapper with the error message “not supported”- This problem arises because Windows has released updates that have broken the program. The solution is to replace the rdpwrap.ini file in the installation folder of the program (C:\Program Files\RDP Wrapper). To download the new file, please go to the following
link.
https://www.rise.company/upload/uplo...2391767310.jpg
Location of the file to be replaced Now, in order to replace the file, it is necessary to stop the remote desktop service. If you don’t, the file will issue an access denied warning. So open a command prompt with administrative privileges and type the following command:
كود:
net stop termservice
Then replaces the rdpwrap.ini file in the installation folder. And at the same command prompt with administrative privileges, please run the following command to restart the remote desktop protocol
كود:
net start termservice
Once the protocol starts, please go to the program folder and re-run RDPConf.exe. If you have done everything correctly, the result of the configuration window should be as follows:
https://www.rise.company/upload/uplo...2239183711.jpg
RDP Wrapper running successfully By activating the program it will be possible to enable multiple remote desktops in Windows Server 2019.
Connecting Multiple Remote Desktop Users to Windows Server 2019
Finally, we will check if it is possible to connect more than two users per remote desktop. To achieve this, we will connect from a Windows 10 computer. Please follow the directions in this
article. Here you can see the 5 remote writer users connected simultaneously from a Windows 10 computer.
https://www.rise.company/upload/uplo...2391849412.jpg
Multiple remote desktop users In the following image, you can see the 5 users running in the task manager.
https://www.rise.company/upload/uplo...2391923213.jpg
Task manager showing all remote desktop users running. In the final analysis, we have seen how to enable multiple remote desktops on Windows Server 2019. With these instructions, it is possible to bypass the restrictions imposed by Microsoft and be able to connect more than two desktops. Even if Windows updates damage the program, we learned how to solve the problem. I hope you enjoyed the tutorial as much as I did. Greetings and see you soon!
