تركيب كاميرا مراقبة فى المصعد / الاسانسير بدون سلك Elevator / Lift Camera | Wireless
كيفية تركيب كاميرا مراقبة Security Camera فى الاسانسير - بدون سلك Wireless
كاميرا مراقبة صغيرة للمصعد - كاميرا زاوية Corner - كاميرا مثلث CCTV
تركيب كاميرا مراقبة فى مصعد وايرليس CCTV LIFT Wireless (Elevator Wireless CCTV)
Wireless Bridge for Elevator hikvision - Wireless Transmitter Receiver
تركيب كاميرا مراقبة فى مصعد بدون سلك
https://www.youtube.com/watch?v=v6tScltGxwY
كابينة المصعد متحركة فلا يفضل معها تمديد أسلاك للكاميرا , لذلك سيتم تثبيت الكاميرات في الكابينة وتوصيلها بجهاز مرسل " Video Transmitter " عن طريق كابل coax cable أو Ethernet Cable , ويتم تثبيت جهاز مستقبل " Video Receiver " بأسفل البئر أو في أعلي البئر , ويتم توصيل جهاز المستقبل بجهاز التسجيل عن طريق كابل مثل كاميرات المراقبة التقليدية .
Wireless Video Transmission System for Elevator Camera
https://www.rise.company/forum/image...2019/09/57.jpg
- The HD-ELT3 camera mounted in the corner of the elevator cabin and hard wired to the video encoder using RG59 coax cable and BNC connectors. Installers can use a spool of RG59 cable or pre-made coax cable for HD security cameras to wire the camera to the video encoder. The same cable is used to wire the decoder to the DVR. You can see close-up images of the inside of the encoder and decoder below - to better understand how to wire them.
- The video encoder and transmitting antenna are mounted to the underside of the elevator cabin (see installation diagram below).
- The video encoder is connected to the wireless transmitter antenna using CAT5 cable.
- There are dip switches on the 2 antennas that are used to specify which antenna is the transmitter and receiver. There are also dip switches to specify the wireless frequency to use. The frequency must be the same on both antennas.
- The receiver wireless antenna and video decoder box are mounted to the floor below the elevator cabin (in the elevator shaft).
- The receiver antenna is wired to the decoder box using the supplied CAT5 jumper cable.
- The BNC video output of the video decoder is connected to one of the BNC video inputs on a DVR or monitor.
اقتباس:
The wireless video can be transmitted up to 762 meters without interference and latency.
The transmitter and receiver are pre-configured to connect to each other.
There is no complicated software configuration that needs to take place.
Elevator Camera Installation
https://www.rise.company/forum/image...2019/09/58.jpg
This is what the installation looks like in an elevator shaft.
Video Transmitter / Video Receiver
These closeup images show the inside of the video transmitter and receiver boxes with the covers removed. This will help installers better understand how easy these systems are to wire.
https://www.rise.company/forum/image...2019/09/61.jpg
- The CAT-5 terminal labeled "To Antenna" connects to the LAN2 port on the transmitting antenna. This cable uses POE to provide power to the antenna.
- The 12V DC / 2 Amp power supply that is included with this system is connected to POWER IN. This 2 Amp power supply is used to power both the antenna and security camera.
- Siamese cable can be used to connect the Camera Power and the Video IN to the security camera that is mounted in the cabin of the elevator.
https://www.rise.company/forum/image...2019/09/62.jpg
- The CAT-5 terminal labeled "To Antenna" connects to the LAN2 port of the receiver antenna. This cable uses POE to provide power to the antenna.
- The 12V DC / 1 Amp power supply that is included with this system is connected to this Power In.
################################################
Wireless Elevator Camera System
Wide Angle Elevator Camera (HD Video)
################################################
يتم تثبيت كاميرة المراقبة في زاوية أو ركن المصعد في المنطقة العلوية , ويوجد كاميرات تكون علي شكل مثلث مخصصة للمصاعد حيث تقوم بكشف وتصوير كل ما في داخل كابينة المصعد وتقليل النقاط العمياء , يتم تثبيت الكاميرات بسهولة عن طريق البراغي .
https://www.rise.company/forum/image...2019/09/63.jpg
https://www.rise.company/forum/image...2019/09/69.jpg
Video Encoder & Wireless Transmitter
https://www.rise.company/forum/image...2019/09/64.jpg
The wireless transmitter consists of a video encoder box and a wireless antenna. Both are typically installed on the underside exterior of the elevator cabin. The security camera inside the elevator cabin is hard wired to the video encoder box using RG59 coax cable. The included CAT5 network cable connects the video encoder to the wireless antenna.
Video Decoder & Wireless Receiver
https://www.rise.company/forum/image...2019/09/65.jpg
The wireless receiver consists of a video decoder box and a wireless antenna. Both are typically installed at the base of the elevator shaft, with the receiving antenna pointed directly at the transmitting antenna (installed on the bottom of the cabin). The included CAT5 network cable connects the video decoder to the wireless antenna.
Installation Mounts
https://www.rise.company/forum/image...2019/09/66.jpg
Two of these installation mounts are included. One for the video encoder box and one for the video decoder box.
https://www.rise.company/forum/image...2019/09/67.jpg
This is what the installation mounts looks like that are included for the two wireless antennas.
Power Supplies
https://www.rise.company/forum/image...2019/09/68.jpg
Two 12V DC power supplies are included. The larger 2 Amp power supply connects to the transmitter box. The smaller 1 Amp power supply connects to the receiver box. The raw cables simply connect to the 2.1mm plugs using screw terminals
ملحوظة هامة : هذه مقالة لشرح الفكرة وليست خدمة مقدمة
